Putsch: Unterschied zwischen den Versionen

Aus Planetenwiki
Wechseln zu: Navigation, Suche
(Command table)
(Command table)
Zeile 225: Zeile 225:
  
 
{| class="wikitable"
 
{| class="wikitable"
|+ Network roles
+
|+ commads
 
|-
 
|-
 
! command !! name !! data packet !! designation
 
! command !! name !! data packet !! designation

Version vom 5. Februar 2023, 19:05 Uhr

Putsch ist ein interaktives Theaterstück vom Planetenparty Prinzip in Koproduktion mit dem Landestheater Linz und LaStrada Graz.


LoRa Netzwerk

Mobile

Wir verwenden Module im Frequenzbereich 433 MHz. Das ist die niedrigste Frequenz mit der größten Reichweite.
RSSID Signal bis zu -100db. (bis zu -80db ist eigentlich eine gute Signalstärke)

Hardware

Microcontroller

The WEMOS D1 mini Lite[1] boards were chosen to realise the LoRa hardware. They feature a ESP8285[2] from Espressif

WEMOS D1 mini Lite

Pitfalls

Special care has to be taken with Pin D3 on the WEMOS D1 mini Lite, as if this pin is held-low while startup, the ESP8285 goes into boot-mode. This causes chaos.

References

[1] WEMOS D1 mini lite homepage: https://www.wemos.cc/en/latest/d1/d1_mini_lite.html

[2] Espressif ESP8285 datasheet: https://www.espressif.com/sites/default/files/documentation/0a-esp8285_datasheet_en.pdf

LoRa Transciever-Modules

For receiving and sending LoRa-data, Ra-02 LoRa modules[3] from Ai-thinker are used. They use a Semtec[1] SX1278 chip[2].

Ra-02 module

Ra-02

The DIO0 pins on the Ra-02 can be ignored for our application. [2] Says that those pins are custom pins that can be software-configured. Antennas for those modules are set seperately because the carrier-frequency can be set via SPI on the SX1278.

Semtec SX1278

According to the datasheet they have 100 mW constant RF output and a programmable bit rate up to 300 kbps. Some parameters including the bitrate can be programmed via SPI. Range and stability are always a tradeoff, that is further described in [2, page 25]. The parameters Spreading Factor, Coding Rate and Signal Bandwidth can therefore be set.

"spreading factor and error correction rate are design variables that allow the designer to optimise the trade-off between occupied bandwidth, data rate, link budget improvement and immunity to interference" - [2, page 25]

Pitfalls

If the maximum Bandwidth (500kKz) on the SX1278 is selected, other paramters have to be adapted. (I try to find that statement in the datasheet again)

References

[1] Semtec website: https://www.semtech.com/products/wireless-rf/lora-connect/sx1278

[2] Semtec SX1278 dataheet: https://cdn-shop.adafruit.com/product-files/3179/sx1276_77_78_79.pdf

[3] Ai-thinker Ra-02 LoRa modules: https://docs.ai-thinker.com/_media/lora/docs/c048ps01a1_ra-02_product_specification_v1.1.pdf

Displays

As a display, a so called 0.91 OLED[1] Display is used. Manufacturer unknown. It is connected via SPI.

References

[1] AZ-delivery product link: https://www.az-delivery.de/products/0-91-zoll-i2c-oled-display

Electromechanical interface

The LoRa boards have a button and a potentiometer. The button is used to change the device mode. The potentiometer is used to change a value in the range of 1-10.

Button State-Diagram

Software

Rollen im Netzwerk

Gateway

Der Gateway ist an einen Computer angeschlossen und somit Schnittstelle zur Spielelogik.


The gateway knows several modes.

Game mode

Game mode is ment to be the reguar interface to the game-logic. The gateway sends any command received via serial.

manual mode

In manual mode a command can be entered via serial promts.

Illuminate mode

In Illuminate-mode, the network illuminates its boarders. It is used fo measuring the reach of the network. Therefore the gateway sends a broadcast. Every repeater that receives the broadcast waits a random amount of time before it resends the message. The RSSI can be measured to determine the signal strength to any repeater.

timing diagram illumnate mode
Stationary

Sind Netzwerkteilnehmer die sich nicht bewegen können. (z.B. Drucker)

Node oder Repeater
Mobile

Sind Netzwerkteilnehmer die sich bewegen können oder auch Radios, die sich zwar nicht bewegen aber ansonsten baugleich sind, mit einem Audioboard dabei. (Radios + Spielerinnen)


Repeater

Dienen ausschließlich zum Wiederholen des Funksignals und adressieren der Teilnehmer – somit ist der Netzwerkaufbau etwas unabhängiger vom Spiel-Aufbau. Erfüllen also die Funktion eines Repeaters. A repeater must know two things:

1) Should it repeat the packet in order that it is passed to the receiver?

1) Should it repeat the packet in order that it is passed to the gateway?

This is realised by storing three arrays, where the array-size equals the maximum subnets. The first index in one array stores the repeaters next neighbours address. By reading it out, the repeater can determine if it is the next possible sender. By scanning the other two arrays, it can determine if it should repeat the packet. One array is for sending from the gateway, the other is for sending back to the gateway.

network situation

As an example we can look ate node 3 with 9 maximum nodes.

neighbour of node 3
5 6 0 0 0 0 0 0 0 0
to gateway array of node 3
2 1 0 0 0 0 0 0 0 0
from gateway array of node 3
5 6 0 0 0 0 0 0 0 0
Messgerät

Das Messgerät zeigt nur die Signalstärke und das subnet an.

Messgerät

Combining LoRa with WLAN

To increase speed, LoRa is going to be combined with WLAN. As measurements showed, bigger packet-sizes do not have as much negative impact on the network speed as much sending. Therefore WLAN Acces Points are implemented.


Idea of combining LoRa with WLAN

A WLAN Acces Point is treaded like a stationary device. It buffers all necessary data of all devices, connected via WLAN to it. With a special command, a bigger packet can be read out, containing all WLAN-devices data.

Lora Packet-Structure

Our initial idea was to send many small packets, to increase data throughput. However measurements showed that the send-process comsumes more time than increasing the packet size. So less but bigger packets seem to be faster than more but smaller packets.

Regular send Lora-packet (from gateway)
Byte: 1 2 3 4 5 6
Purpose: receiver-address command data sender-address (1) packet-id subnet
Possible Lora-return-packet (to gateway)
Byte: 1 2 3 4 5 6
Purpose: receiver-address (1) command data sender-address packet-id position

On WLAN Access Points, a bigger packet can be read out.

Return Lora-packet for WAPs (to gateway)
Byte: 1 2 3 4 5 6 ... n-2 n-1 n
Purpose: receiver-address (1) amount of data (k) packet-id data 1 sender-address 1 position 1 ... data k sender-address k position k

Network address table

The role of a LoRa network device is set by its network address. This saves a seperate handling of the role beside its addressing. If the device is the gateway or a repeater, its address equals also the subnet the device is standing for.

Network roles
address purpose
0 invalid
1 gateway
2-9 repeater
10-49 mobile endnodes
50-149 stationary endnodes
254 broadcast
255 invalid

Address 0 and 255 are invalid, as there might be a hardware shortcut to GND or VCC in this case. Address 254 is for broadcasting. This means if the gateway addresses 254, every network device is receiving.

Command table

This table shows the commands that can be sent via LoRa. The designation is ment to be a unique 4-Char name for defines.

commads
command name data packet designation
0 invalid - -
246 WLAN member data answer special data format WMDA
247 WLAN member data request - WMDR
249 illuminate - ILLU
250 - 254 unused - -
253 ping answer RSSI of received ping PNGA
254 ping request - PNGR
255 invalid - -

COMMENT: The command numbers need to be rearranged/sorted once it's finished!

Hardware communication libraries

Token Pass System

Innere Stimme

Knochenschallkopfhörer Interface

Das Publikum wird begleitet durch eine sogenannte innere Stimme, die im eigenen Kopf drin zu einem spricht. Um diesen Effekt zu unterstützen werden Knochenschallkopfhörer benutzt, die den Schall über den Schädelknochen übertragen und somit die Ohren für Umgebungsgeräusche frei bleiben, während Audiofiles abgespielt werden.

Wir verwenden Conductor Transducer von adafruit.

Olimex Audioboard

Audio Modul für Radios und Publikum

SD Karten Bespielprogramm

Programm, dass automatisch die SD Karten mit unserer Ordnerstruktur von Audiofiles bespielt, um große Zeitverluste und Fehler durch manuelles Kopieren zu vermeiden.

SD Karten Abspielprogramm

Enthält Funktionen das Abspielen der Audiofiles dynamisch gestalten, die flüssiges Wechseln zwischen Quests oder spontane Begegnungen inmitten von laufenden Quests ermöglichen. Geht Hand in Hand mit einer übersichtlichen Ordnerstruktur und sehr kleinen Snippets der Audioaufnahmen, die Sprünge zwischen Ordnern/Quests erlauben, sowie "Zurückkehren" zu bereits angefangenen Quests.

Ortung der mobilen Clients im Spiel

Infrarot

Bluetooth Beacons

Spiellogik

Grobes Konzept zur Sofware Architektur

Architektur

Event Hub

The Event Hub is a piece of software

  • receiving events from the LORA gateway and adaptor:ex
  • receiving commands from the Director UI and the Actor UI via the Control Server
  • changing the state in adaptor:ex
  • sending commands to Players via the LORA gateway
  • providing and pushing data to the Control Server (and thus, to the Director UI and the Actor UI)
  • communicating with peripherals like printers

Das echte Büro

Drucker-Hack

Radio-Hack

Aktenschrank-Hack

Inhalt